Backyard Bot HQ is reader-supported: we may earn a commission when you buy through links on this site, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. How this works.
A LUBA 2 that won’t join your WiFi usually has a network setup problem, not a broken mower. Mammotion says LUBA supports 2.4 GHz WiFi only. Start by checking the band your router offers, the signal where the mower sits, and how close your phone is during setup.
Use a 2.4 GHz network, keep your phone within 10 ft during setup, and test with a phone hotspot before blaming the mower.
How the LUBA 2 connects
It helps to know which link does what. The LUBA 2 manual lists three: Bluetooth connects the mower to your phone, while WiFi and 4G connect it to the internet. During setup, the app connects to the mower over Bluetooth and then sets up its network.
There’s a fourth link that people often mix up with WiFi. The RTK reference station talks to the mower over its own radio. If the app’s status bar shows “Connection to Ref. Station: None,” that’s the RTK link, not WiFi (WiFi has its own icon on the status bar). The manual’s fixes there are to check the station’s power, confirm its radio antenna is installed and re-pair it.
Fixes in order, easiest first
1. Stand next to the mower during setup
The manual says to keep your phone within 3 m (10 ft) of the LUBA when adding it. Keep Bluetooth on. If the app asks for Bluetooth, location or local network access, allow them; the LUBA mini 2 manual recommends granting all three.
2. Give it a 2.4 GHz network
This is the big one. Mammotion’s support page says LUBA only supports 2.4 GHz and tells you to check whether your network is 2.4 GHz or offers both 2.4 GHz and 5 GHz.
If your router uses one network name for both bands, our advice is to log in to it (or its app) and either split the bands into two names or set up a guest network that’s 2.4 GHz only, then point the LUBA at that. Type the password carefully; capital letters count.
3. Move the mower closer to the router
Distance and walls block the signal. Mammotion’s support page says to move LUBA closer to the router, especially before a firmware update. A mower parked by the back fence may connect fine in the garage and then drop out on the lawn. If that’s your setup, an outdoor access point or a mesh node near the yard can help. Check the mesh note below first.
4. Try your phone’s hotspot
Turn on your phone’s hotspot and connect the LUBA to that. This is Mammotion’s own suggestion. Choose 2.4 GHz if your phone lets you pick the hotspot band. When it connects, the problem is likely with your home network rather than the mower. If it can’t join either network, move on to the key reset.
5. Reseat the key
Mammotion’s reset for a LUBA that won’t join any network:
- Power off the LUBA.
- Unplug the key from the back of the mower.
- Plug it back in.
- Power the LUBA on and try again.
6. Change the network from the app
Once the mower is in your account, you don’t need to start over to change networks. The LUBA 2 manual puts this under device settings, in Network settings. Use it after a router swap or a password change.
A factory reset is the last resort. The manual warns that it wipes all logs and saved WiFi passwords, so send a log first through Feedback in the same settings menu.
The mesh network problem
Mesh systems can trip up the LUBA 2. One owner of a LUBA 2 AWD 5000X wrote in April 2026 that the mower would only join the main modem’s WiFi, not the nodes of a four-node mesh system already set to 2.4 GHz. Their phone connected to every node without trouble. The router maker’s support asked for more details, and no fix was posted.
If you see the same thing, try connecting the mower to the main router’s network, or set up a separate 2.4 GHz network just for the mower. Then check which access point it ends up on.
When WiFi won’t reach the lawn: use 4G
Some yards are simply too far from the house. The LUBA 2 has an optional 4G SIM card tray at the back, and the manual covers installing a SIM. With 4G, the mower stays online for the app and location tracking even out of WiFi range.
The LUBA mini 2 goes further. Its manual has you activate a built-in SIM during setup and says you can skip WiFi entirely on 4G, though it still recommends WiFi for best performance. If a dead zone is the whole problem, look at the LUBA mini 2 AWD before you buy another access point, or use the robot mower finder to compare other models for your yard.
What owners report
Some owners report connection and setup trouble in Mammotion’s customer reviews. In November 2026, one owner who praised the cut quality said connecting the mower took at least an hour and sometimes failed, and found support mostly automated. In late October, another reviewer described more than 50 hours getting their mower properly set up while support kept suggesting firmware updates and settings they had already changed.
The pattern is worth knowing before you call. Go through steps 1 to 5 and note what happened at each, so support can skip straight to the logs.
Mammotion’s app also leans on Bluetooth more than some rivals do. One independent group test found that only two brands’ apps offered remote control without a Bluetooth connection, and Mammotion wasn’t one of them. Don’t expect to drive the LUBA from the couch if it’s out of Bluetooth range.
When to contact Mammotion
Contact Mammotion if the LUBA won’t join your phone’s hotspot after a key reset, or if it connects and then drops while sitting next to the router. Send a log from the app first and include your router model.
For other Mammotion models and current specs, see our Mammotion brand page.
Bottom line
Start with a dedicated 2.4 GHz network and a phone standing next to the mower during setup. If the hotspot test fails too, reseat the key, send logs and let Mammotion take it from there.