Backyard Bot HQ is reader-supported: we may earn a commission when you buy through links on this site, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. How this works.
If your LUBA won’t charge, look at the light on the charging station before anything else. A flashing green light means it’s charging. With the mower docked, a solid green light means it’s either full or not charging. If the mower won’t power on in that state, Mammotion’s first fix is to unplug its security key and plug it back in. A red light on the station means the station itself has a fault.
Read the dock light, reseat the key, clean the charging pads, then check the 39 to 113°F charging range before calling Mammotion.
What the charging station light means
The two manuals describe the green light slightly differently, so check which mower you own.
| Station light | LUBA 2 AWD (manual V2.0) | LUBA mini 2 AWD (manual v1.0) |
|---|---|---|
| Flashing green | Charging | Mower is docked |
| Solid green | Fully charged, or not charging | Mower isn’t in the station |
| Red | An error has occurred | Station malfunction |
| Off | Not listed | No power |
Checked 21 Nov 2026.
So a solid green light with a LUBA 2 sitting on the dock is ambiguous: either it’s full or it isn’t taking a charge. Check the battery level in the Mammotion app. On a LUBA mini 2, solid green with the mower docked means the dock doesn’t see it at all.
The mower has its own light too. Mammotion’s installation guide says the side light on the robot turns red when it’s properly docked. On the LUBA 2, a very fast red flash on the side light means charging is in progress, and solid red with the mower still on the dock means charging has finished.
Safety first
Use only the power supply that came with the mower. Both manuals carry that warning, and the two adapters aren’t the same: the LUBA 2 charger puts out 25.2 V DC at 7 A, while the LUBA mini 2 supply is 27 V DC at 3 A. Unplug the station before cleaning the pads. Mammotion’s manual also warns never to open or repair the battery yourself.
Fixes in order, easiest first
1. Check power to the dock
If the station light is off, the problem is upstream. Test the outlet with another device, check the outdoor GFCI hasn’t tripped, and push the adapter cable firmly into the station. If you have a multimeter, the cable should read close to the adapter’s rated output. One LUBA mini AWD owner measured 28 V at the cradle, which ruled out power as the cause.
2. Reseat the security key
This is Mammotion’s own first fix for a LUBA that won’t turn on while docked and shows a solid green dock light. Unplug the key (in the rear keyhole on the LUBA 2; on top of the LUBA mini 2), plug it back in, and see whether the mower powers on. On the LUBA mini 2, a slow blinking red side light can also mean the key isn’t seated properly.
3. Clean the charging pads and the infrared window
The LUBA docks using an infrared receiver (on the rear of the LUBA 2, underneath on the LUBA mini 2), and the station has its own infrared transmitter. With the station unplugged, clean the station’s infrared window and the charging contacts with a brush and a clean cloth, as the LUBA mini 2 manual and Mammotion’s LUBA 3 AWD maintenance guide describe. Clear grass and mud from the base plate. Check the pads for corrosion while you’re there. For winter storage, Mammotion’s support guide allows anti-corrosion lubricant on the charging pads and connectors only.
4. Level the dock and clear the approach
The LUBA 2 manual is strict about this. The base plate must not be bent or tilted, and it shouldn’t sit on a slope, uneven ground or thick grass that gives way under the mower’s weight. Mammotion’s installation guide asks for at least 5 ft (1.5 m) of clear space in front and on both sides. If the dock has sunk into soft soil, pull the stakes, flatten the ground and reset it.
To test the docking, drive the mower about 5 ft (1.5 m) in front of the station with its back facing the dock, then press Auto-return followed by Start. The LUBA 2 manual describes this same routine for first-time docking.
5. Check the temperature
Both manuals list 39 to 113°F (4 to 45°C) as the charging range. Outside it, charging may not start or may pause. That matters at both ends of the season: a frosty November morning is below the bottom of the range, and a heat wave can push past the top. Give the mower time to warm up or cool down before you assume a fault.
Low battery behavior can also look like a charging fault. The LUBA 2 returns to charge on its own below 15%, and its manual says that after a low battery fault it carries on working once it’s charged back to 80%. A LUBA sitting on the dock at 60% may simply be waiting.
6. Reset, then send logs
If the key reset doesn’t work, Mammotion’s next step is a factory reset. The LUBA 2 manual notes that a factory reset clears all logs and saved Wi-Fi passwords, so send a log first: in the app, go to Settings, then Feedback, and attach up to 5 photos and 1 video.
When it’s a repair, not a fix
Mammotion’s support page lists two cases that need a repair. One is a LUBA that turns on in the dock but shows 0% battery even after a long charge. The other is one that won’t turn on at all after the steps above. Contact Mammotion through the request form on its support site.
Warranty terms vary by model, so check the paperwork for yours. The LUBA 2 manual (V2.0) lists 2 years on the main body and battery, and 1 year on the charging station and RTK antenna.
What owners report
Charging and docking problems are one of the recurring complaints in Mammotion’s customer reviews, alongside slow repairs and scripted support replies. Experiences with support vary a lot. One owner wrote in October 2026 that their charging station developed a fault under warranty and the replacement arrived five days later. Another owner said their mower stopped charging after the warranty ended, and Mammotion still arranged shipping and repair.
Not every case is that smooth. One LUBA mini AWD owner cleaned the contacts, reseated the mower and confirmed power at the cradle, and still got a solid green light and no charge. The advice they got was to contact Mammotion, which can read the mower’s logs. That’s the right call once you’ve done steps 1 to 5.
What about the original LUBA mini?
The steps above apply to it too. Mammotion’s installation guide covers the LUBA mini AWD alongside the LUBA 2 and LUBA mini 2, and its support article on a LUBA that won’t turn on is written for LUBA mowers in general. The light meanings may differ, so check your manual’s indicator table.
Bottom line
Read the dock light, reseat the key, clean the pads and infrared window, level the dock, and wait out extreme temperatures. If the battery still reads 0% after a long charge, send a log and open a repair request. If you’re weighing a replacement, the LUBA mini 2 AWD and LUBA 3 AWD are on sale now, and our Mammotion brand page lists the rest.